INVERTERS FOR SOLAR / BATTERY STORAGE

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.   Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC010015200R GTIN 8719076025337 Battery Voltage 12/24V Auto Select Rated Charge Current 15A Nominal PV Power, 12V 220W Nominal PV Power, 24V 440W Max. PV Short Circuit Current 15A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.   Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98 %. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV-712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) Real-time data display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC010070300 GTIN 8719076025528 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 70A Nominal PV Power, 12V 1000W Nominal PV Power, 24V 2000W Max. PV Short Circuit Current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H215 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

Part No: SUN3KTL-L1 Storage Systems - Hybrid Inverter Huawei Fusion Home SUN2000L1 - 3/ 3.68 / 5 /6KTL The Smart Energy Controller (SUN2000- 3 / 3.68 / 5 / 6KTL-L1) is Huawei new single-Phase inverter and is direct compatible with their own Huawei Luna battery Product Features Direct compatible with Luna battery and is Plug and Play and no extra devices is needed AI Self leaning new arc detection Is compatible with the Sun2000-450W-P optimizer Simple commissioning by APP Auto-detection of system equipment Registering your plant by scanning any device Energy Flow illustration Real-time data at anytime and anywhere Performance data back-up Physical & logical module layout Module -level performance monitoring Smart I-V Diagnosis Smart dongle Plug and Play (LAN or 4G dongle available) Smart dongle support up to 10 inverters IP65 Can be installed without batteries as 'battery ready' Max 3 batteries per inverter Supplier Part No: 01075350 Weight: 12 kg Rated Power: 3,000 W Min PPT Voltage: 90 V Max PPT Voltage: 560 V DC Startup Voltage: 100 V DC Shutdown Voltage: 90 V Max Input Voltage: 600 V Max DC Power: 4,500 W Max AC Power (5 Minutes): 3,000 W Surge AC Power (1 Second): 3,301 W Max DC Current: 25 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: Amphenol H4   Included Connectors: 2 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: Yes. Data Sheet Huawei L1 Installation Manual Huawei L1 - Quick guide

Read more less

 Part No: X3-8000T Storage Systems - Hybrid Inverter X3-HYBRID-5.0T / X3-HYBRID-6.0T / X3-HYBRID-8.0T / X3-HYBRID-10.0T X3-Hybrid HV Three Phase   The new X3-Hybrid High-Voltage is the latest incarnation in battery storage inverters from SolaX. The X3 ranges in size from 5 to 10kW and has the ability to install multiple inverters in parallel . It’s equipped with a built-in EPS (Emergency Power Supply), has multiple communication options (additional Wifi or LAN sticks can be purchased separately) and can be controlled remotely using the SolaX monitoring app, X-Cloud.   Additional features: Unbalanced phase load supported Up to 25.2kWh storage per inverter Up to 10kW Max charge/discharge G100 Export Limitation compliant Suitable for grid trading applications Charging from grid possible Fanless design Please note the minimum number of batteries per X3 Hybrid inverter is 2 and maximum of 4. Please note batteries need to be the same capacity, it’s not possible to connect both 4.5kWh and 6.3kWh to one inverter.   Please note this inverter is not EN50438 IE certified for Ireland.  Supplier Part No: X3-Hybrid 8.0E Weight: 48 kg Rated Power: 8,000 W Min PPT Voltage: 180 V Max PPT Voltage: 950 V DC Startup Voltage: 180 V DC Shutdown Voltage: 180 V Max Input Voltage: 1,000 V Max DC Power: 12,000 W Max AC Power (5 Minutes): 8,000 W Surge AC Power (1 Second): 8,800 W Max DC Current: 24 A Max DC Inputs: 3 Has DC Fuses: 0 Connector: SUNCLIX   Included Connectors: 2 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: No Warranty: 5 years Data Sheet Solax X3 Hybrid EN

Read more less

Part No: SOL-0.7-MINI-S6-DC Inverters - Main Units Rating: 700W Phases: 1 The All New Solis Mini 6S Series Grid-tie Inverter. Compact and lightweight design, for easy installation. Fanless, minimal noise, producing less than 20 dBA. Compatible with high-efficiency modules and bi-facial modules. Product Features Super high frequency switching technology with maximum efficiency of 96.6% Max PV Power of 1.1kW DRM (Demand Response Mode) integrated and backflow power control function for smart grid requirements. Wide voltage range - Ultra low start-up voltage of 60V and max PV input voltage of 600V Intergrated Export Power Manager (EPM) Integrated AFCI (DC arc-fault circuit protection) Integrated DC switch for emergency shut-down of PV power or safe PV maintenance 5-year standard warranty Supplier Part No: S6-GR1P0.7K-M-DC Weight: 7.4 kg Rated Power: 700 W Min PPT Voltage: 60 V Max PPT Voltage: 500 V DC Startup Voltage: 60 V DC Shutdown Voltage: 50 V Max Input Voltage: 600 V Max DC Power: 1,100 W Max AC Power (5 Minutes): 770 W Surge AC Power (1 Second): 770 W Max DC Current: 14 A Max DC Inputs: 1 Has DC Fuses: 0 Connector: MC4   Included Connectors: 1 Euro Efficiency: 95.3 % Transformer: None MPPT Quantity : 1 Has Integrated DC Switch: Yes Warranty: 5 years Designed by world leading research and development team made by professors and specialists from 8 countries, Solis inverters are praised by clients and customs all over the world due to the high quality and reliability with the feature of ultra wide input voltage, precise MPPT algorithm, and Max. efficiency over 97%, which made Ginlong brand one of the most performance-cost inverters in the world. Data Sheet S6-GR1P(0.7-3.6)K-M

Read more less

Part No: SOL-110.0-3PH-5G-AC-DC Inverters - Main Units Rating: 110,000W Phases: 3 Solis-110K-5G 3phase Inverter Product Features Max. 13A per string (26A per MPPT), 150% DC overloading capability 10 individual MPPT, lower mismatch loss Efficient logic algorithm, over 99% max. Efficiency String monitoring, shorter O&M time Remote & local intelligent IV scan function Leakage current repression technology Volt-watt work mode integrated DC input reverse alarm Optional anti-PID function integrated Reactive power compensation function Integrated AFCI (DC arc-fault circuit protection) Type ll surge protection for DC and AC Intergrated DC and AC switch Supplier Part No:  SOL-110.0-3PH-5G-AC-DC Weight: 84 kg Rated Power: 110,000 W Min PPT Voltage: 180 V Max PPT Voltage: 1,000 V DC Startup Voltage: 195 V DC Shutdown Voltage: 180 V Max Input Voltage: 1,000 V Max DC Power: 165,000 W Max AC Power (5 Minutes): 110,000 W Surge AC Power (1 Second): 110,000 W Max DC Current: 260 A Max DC Inputs: 20 Has DC Fuses: 0 Connector: MC4   Included Connectors: 32 Euro Efficiency: 98.3 % Transformer: None MPPT Quantity : 10 Has Integrated DC Switch: Yes Warranty: 5 years Designed by world leading research and development team made by professors and specialists from 8 countries, Solis inverters are praised by clients and customs all over the world due to the high quality and reliability with the feature of ultra wide input voltage, precise MPPT algorithm, and Max. efficiency over 97%, which made Ginlong brand one of the most performance-cost inverters in the world. Data Sheet (100-125)K -5G

Read more less

Part No: GROWATT-1000-TL-X Inverters - Main Units Rating: 1,000W Phases: 1 Growatt inverters are designed specifically for residential rooftop applications. With a maximum efficiency of 97% and a wide input voltage range, this robust inverter is perfect for residential installations. The TL-X range has a single MPPT.  The Growatt inverter range has the following leading-edge technology. MPPT tracking accuracy of 99% Max. Efficiency 97.6%, European Efficiency 96.5% Transformerless design, offer lighter and more convenient installation  Power factor continuously adjustable Flexible interface Touch key & OLED display This is the Non-DC version   UK: The Installer Code Policy is in the process of being introduced in the UK and Ireland. It means all installers will need to register an ‘Installer Code’ for using the Growatt monitoring platform. This installer code can be provided to the end user by the installer to allow for the viewing of your customers devices from your installer-level monitoring account. For more information, please refer to the following document: Growatt Installer Code policy   Supplier Part No: Growatt 1000 TL-X Weight: 6 kg Rated Power: 1,000 W Min PPT Voltage: 50 V Max PPT Voltage: 500 V DC Startup Voltage: 50 V DC Shutdown Voltage: 50 V Max Input Voltage: 500 V Max DC Power: 1,400 W Max AC Power (5 Minutes): 1,000 W Surge AC Power (1 Second): 1,000 W Max DC Current: 13 A Max DC Inputs: 1 Has DC Fuses: 0 Connector: Amphenol H4   Included Connectors: 1 Euro Efficiency: 96.5 % Transformer: None MPPT Quantity : 1 Has Integrated DC Switch: No Warranty: 10 years Application Note TL-X Series Brochure Growatt UK Products Brochure CE Declaration of Conformity Data Sheet MIC 750_3300TL-X G100 certification Growatt MIC 750-3300TL-X G98 Certificate 750TL-X - 3300TL-X Installation Manual MIC 750-3300TL-X Installation Manual Quick Guide MIC 750-3300TL-X Warranty Card White Paper New Installer Code Registration Process

Read more less

Part No: GROWATT-5000-TL-XE-DC Inverters - Main Units Rating: 5,000W Phases: 1 Growatt inverters are designed for specifically for residential rooftop applications. With a maximum efficiency of 98% and wide input voltage range, this robust inverter is perfect for most domestic installs Leading - edge Technology ·       Double MPPT Tracker, MPPT tracking accuracy more than 99.5% ·       Max. Efficiency 98%, European Efficiency 97% ·       Transformerless design and high power density, offer lighter and ·       more convenient installation ·       Comes with10 years warranty ·       Power factor continuously adjustable ·       Flexible communication connection ·       Comply with European, Asia-Pacific safety regulations   Built in DC isolator.  UK only: This inverter has been tested and certified according to G99, but only for units having most recent Firmware and Hardware version. Please check if the unit you are purchasing meets that criteria and if in doubt, please update the inverter firmware.   UK: The Installer Code Policy is in the process of being introduced in the UK and Ireland. It means all installers will need to register an ‘Installer Code’ for using the Growatt monitoring platform. This installer code can be provided to the end user by the installer to allow for the viewing of your customers devices from your installer-level monitoring account. For more information, please refer to the following document: Growatt Installer Code policy Please note: In order to achieve anti reflux function on TL-X and TL-XE range, you must use Meter SPM-E. Using a CT clamp to try and achieve this is not possible. Please contact us for more details. Supplier Part No:  GROWATT-5000-TL-XE -DC Weight: 10.8 kg Rated Power: 5,000 W Min PPT Voltage: 100 V Max PPT Voltage: 550 V DC Startup Voltage: 100 V DC Shutdown Voltage: 80 V Max Input Voltage: 550 V Max DC Power: 7,000 W Max AC Power (5 Minutes): 5,000 W Surge AC Power (1 Second): 5,000 W Max DC Current: 25 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: Amphenol H4   Included Connectors: 2 Euro Efficiency: 97.5 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 10 years Application Note TL-XE Series CE Declaration of Conformity Data Sheet MIN 2500-6000 TL-XE EN50549 G100 certification Growatt MIN 2500-6000TL-XE G99 Certificate IEC Certificate Independant Test Report SGS ENAC Installation Manual Growatt X-XE Installation Manual Quick Guide Warranty Growatt Warranty Card-UK White Paper New Installer Code Registration Process

Read more less

Part No: GROWATT-3000-TL-XE-DC Inverters - Main Units Rating: 3,000W Phases: 1 Growatt inverters are designed for specifically for residential rooftop applications. With a maximum efficiency of 98% and wide input voltage range, this robust inverter is perfect for most domestic installs Leading - edge Technology ·       Double MPPT Tracker, MPPT tracking accuracy more than 99.5% ·       Max. Efficiency 98%, European Efficiency 97% ·       Transformerless design and high power density, offer lighter and ·       more convenient installation ·       Comes with10 years warranty ·       Power factor continuously adjustable ·       Flexible communication connection ·       Comply with European, Asia-Pacific safety regulations   Built in DC isolator.  UK only: This inverter has been tested and certified according to G99, but only for units having most recent Firmware and Hardware version. Please check if the unit you are purchasing meets that criteria and if in doubt, please update the inverter firmware.   UK: The Installer Code Policy is in the process of being introduced in the UK and Ireland. It means all installers will need to register an ‘Installer Code’ for using the Growatt monitoring platform. This installer code can be provided to the end user by the installer to allow for the viewing of your customers devices from your installer-level monitoring account. For more information, please refer to the following document: Growatt Installer Code policy Please note: In order to achieve anti reflux function on TL-X and TL-XE range, you must use Meter SPM-E. Using a CT clamp to try and achieve this is not possible. Please contact us for more details. Supplier Part No:  GROWATT-3000-TL-XE-DC Weight: 10.5 kg Rated Power: 3,000 W Min PPT Voltage: 100 V Max PPT Voltage: 500 V DC Startup Voltage: 100 V DC Shutdown Voltage: 80 V Max Input Voltage: 500 V Max DC Power: 4,200 W Max AC Power (5 Minutes): 3,000 W Surge AC Power (1 Second): 3,000 W Max DC Current: 25 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: Amphenol H4   Included Connectors: 2 Euro Efficiency: 97.1 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: Yes Warranty: 10 years

Read more less

Growatt inverters are designed for specifically for residential rooftop applications. With a maximum efficiency of 98% and wide input voltage range, this robust inverter is perfect for most domestic installs Leading - edge Technology ·       Double MPPT Tracker, MPPT tracking accuracy more than 99.5% ·       Max. Efficiency 98%, European Efficiency 97% ·       Transformerless design and high power density, offer lighter and ·       more convenient installation ·       Comes with10 years warranty ·       Power factor continuously adjustable ·       Flexible communication connection ·       Comply with European, Asia-Pacific safety regulations Built in DC isolator.  UK only: This inverter has been tested and certified according to G99, but only for units having most recent Firmware and Hardware version. Please check if the unit you are purchasing meets that criteria and if in doubt, please update the inverter firmware. Click Here For Specs

Read more less

Part No: HUA-BACKUP-BOX-B1 Storage Systems - Accessory Huawei's Backup Box provides automatic detection & switchover providing reliable backup power.  The Backup Box is used in a residential rooftop PV plant system to control the inverter grid-tied or off-grid state. When the grid fails, the inverter switches to the off-grid state and supplies power to off-grid loads in backup mode. When the grid recovers, the inverter switches back to the grid-tied state. The Box is compatible with the following Huawei Inverters: SUN2000-3/4/5/6/8/10KTL-M1 Supplier Part No: 02406150 Weight: 11 kg

Read more less

Part No: SOL-2.5-S6-DT-DC Inverters - Main Units Rating: 2,500W Phases: 1 Solis S6 is the latest generation of residential inverters from Solis. This range of inverters are leaders in affordable small residential and commercial rooftop installations.  Product Features   Maximum string input current 14A   Easy installation: Integrate with export power control function and DRM function.   Max. Efficiency over 97.7% European efficiency over 97.1%   Wide input voltage range for better generation and low startup    Dual MPPT design with precise MPPT algorithm   Export Limitation built in - Requires CT clamp (sold separately)   Integrated AFCI (DC arc-fault circuit protection)   Rated IP66 With built in DC switch.    Supplier Part No: S6-GR1P2.5K DCWeight:11 kgRated Power: 2,500 WMin PPT Voltage: 60 VMax PPT Voltage: 550 VDC Startup Voltage: 60 VDC Shutdown Voltage: 50 VMax Input Voltage: 550 VMax DC Power: 3,750 WMax AC Power (5 Minutes): 2,800 WSurge AC Power (1 Second): 2,800 WMax DC Current: 28 AMax DC Inputs: 2Has DC Fuses: 0Connector: MC4Included Connectors: 2Euro Efficiency: 96.5 %Transformer: NoneMPPT Quantity : 2Has Integrated DC Switch: YesWarranty: 5 yearsClick Here For specs

Read more less

Part No: SOL-3.0-S6-DT-DC Inverters - Main Units Rating: 3,000W Phases: 1 Solis S6 is the latest generation of residential inverters from Solis. This range of inverters are leaders in affordable small residential and commercial rooftop installations.  Product Features   Maximum string input current 14A   Easy installation: Integrate with export power control function and DRM function.   Max. Efficiency over 97.7% European efficiency over 97.1%   Wide input voltage range for better generation and low startup    Dual MPPT design with precise MPPT algorithm   Export Limitation built in - Requires CT clamp (sold separately)   Integrated AFCI (DC arc-fault circuit protection)   Rated IP66 With built in DC switch.    Supplier Part No: S6-GR1P3K-DCWeight: 11.2 kgRated Power: 3,000 WMin PPT Voltage: 60 VMax PPT Voltage: 600 VDC Startup Voltage: 60 VDC Shutdown Voltage: 50 VMax Input Voltage: 600 VMax DC Power: 4,500 WMax AC Power (5 Minutes): 3,300 WSurge AC Power (1 Second): 3,300 W Max DC Current: 28 AMax DC Inputs: 2Has DC Fuses: 0Connector: MC4Included Connectors: 2Euro Efficiency: 96.6 %Transformer: NoneMPPT Quantity : 0Has Integrated DC Switch: YesWarranty: 5 years Click Here For Specs 

Read more less

Part No: SOL-S5-GR3P-6K-DC Inverters - Main Units Rating: 6,000W Phases: 3 Series 5 GR3P Three Phase Grid-Tied Inverter Product Features: Max. efficiency of 98.3%  Type-II over-voltage surge protection for both DC and AC Wide voltage range - Ultra low start-up voltage of 180V and max PV input voltage of 1100V 16A PV string input x 2 Maximum AC output power of 6.6kW  Max PV DC Power of 9kW Integrated AFCI (DC arc-fault circuit protection) IP66 Rated  DC reverse-polarity protection 5-year standard warranty Register on SolisCloud, to support remote upgrade and control. NRS-097-2-1 Certified This product must be installed by a qualified electrician/technician. All installations must adhere to local wiring regulations and standards. SegenSolar will not be held liable for any product malfunctions as a  result of incorrectly installed systems. Supplier Part No: SOL-S5-GR3P-6K-DCWeight: 19.48 kgRated Power: 6,000 WMin PPT Voltage: 180 VMax PPT Voltage: 1,000 VDC Startup Voltage: 180 VDC Shutdown Voltage: 160 VMax Input Voltage: 1,100 VMax DC Power: 9,000 WMax AC Power (5 Minutes): 6,600 WSurge AC Power (1 Second): 6,600 WMax DC Current: 32 AMax DC Inputs: 2Has DC Fuses: 0Connector: MC4 Included Connectors: 4Euro Efficiency: 97.7 %Transformer: NoneMPPT Quantity : 2Has Integrated DC Switch:  YesWarranty: 5 years Click Here For Specs

Read more less

Part No: SOL-S5-GR3P-10K-DC Inverters - Main Units Rating: 10,000W Phases: 3 Series 5 GR3P Three Phase Grid-Tied Inverter Product Features: Max. efficiency of 98.5%  Type-II over-voltage surge protection for both DC and AC Wide voltage range - Ultra low start-up voltage of 180V and max PV input voltage of 1100V 16A PV string input x 2 Maximum AC output power of 11kW  Max PV DC Power of 15kW Integrated AFCI (DC arc-fault circuit protection) IP66 Rated  DC reverse-polarity protection 5-year standard warranty Register on SolisCloud, to support remote upgrade and control. NRS-097-2-1 Certified This product must be installed by a qualified electrician/technician. All installations must adhere to local wiring regulations and standards. SegenSolar will not be held liable for any product malfunctions as a  result of incorrectly installed systems. Supplier Part No: SOL-S5-GR3P-10K-DCWeight: 20.08 kg 10,000 WMin PPT Voltage: 180 VMax PPT Voltage: 1,000 VDC Startup Voltage: 180 VDC Shutdown Voltage: 160 VMax Input Voltage: 1,100 VMax DC Power: 15,000 WMax AC Power (5 Minutes): 11,000 WSurge AC Power (1 Second): 11,000 WMax DC Current: 32 AMax DC Inputs: 2Has DC Fuses: 0Connector: MC4 Included Connectors: 4Euro Efficiency: 97.9 %Transformer: NoneMPPT Quantity : 2Has Integrated DC Switch: YesWarranty: 5 years Click Here For Specs 

Read more less

Part No: SOL-S5-GR3P-12K-DC Inverters - Main Units Rating: 12,000W Phases: 3 Series 5 GR3P Three Phase Grid-Tied Inverter Product Features: Max. efficiency of 98.6%  Type-II over-voltage surge protection for both DC and AC Wide voltage range - Ultra low start-up voltage of 180V and max PV input voltage of 1100V 16A PV string input x 4 Maximum AC output power of 13.2kW  Max PV DC Power of 18kW Integrated AFCI (DC arc-fault circuit protection) IP66 Rated  DC reverse-polarity protection 5-year standardSupplier Part No: SOL-S5-GR3P-12K-DC Weight: 21.78 kg Rated Power: 12,000 WMin PPT Voltage: 180 VMax PPT Voltage: 1,000 VDC Startup Voltage: 180 VDC Shutdown Voltage: 160 VMax Input Voltage: 1,100 VMax DC Power: 18,000 WMax AC Power (5 Minutes): 13,200 WSurge AC Power (1 Second): 13,200 WMax DC Current: 64 AMax DC Inputs: 4Has DC Fuses: 0Connector: MC4 Included Connectors: 8Euro Efficiency: 98 %Transformer: NoneMPPT Quantity : 2Has Integrated DC Switch: YesWarranty: 5 years warranty This product must be installed by a qualified electrician/technician. All installations must adhere to local wiring regulations and standards. SegenSolar will not be held liable for any product malfunctions as a  result of incorrectly installed systems. Click Here For Specs

Read more less

Part No: X3-PRO-25K Inverters - Main Units Rating: 25,000W Phases: 3 X3-Pro-25K G2 High-Effi­ciency Maximum effi­ciency is up to 98.5% Low start up voltage, ultrawide MPPT voltage range 150% oversizing, 110% overloading output Built-in shadow tracking function Safe SPD type II protection both AC&DC ARC protection (Optional) IP66 protection Smart Built-in export power control Intelligent load management - heat pump (Optional) 24 hours operation monitoring Multiple monitoring methods, Pocket WiFi/LAN/4G (Optional) Economic Ultra-high power density Maximum 16A DC input current, support high power solar panel Up to 3 MPPTs, 2 strings per MPPT When installing under G100 there is a requirement to install Solax Chint Three Phase Meter to be compliant.   Supplier Part No: X3 PRO 25kW G2 Weight: 28 kg Rated Power: 25,000 W Min PPT Voltage: 200 V Max PPT Voltage: 960 V DC Startup Voltage: 200 V DC Shutdown Voltage: 180 V Max Input Voltage: 1,000 V Max DC Power: 37,500 W Max AC Power (5 Minutes): 25,000 W Surge AC Power (1 Second): 27,500 W Max DC Current: 32 A Max DC Inputs: 0 Has DC Fuses: 0 Connector: MC4   Included Connectors: 6 Euro Efficiency: 98 % Transformer: None MPPT Quantity : 6 Has Integrated DC Switch: No Warranty: 10 years

Read more less

This is the 4th generation of the SolaX Hybrid range, retaining all the key features of the 3rd generation while making some welcome improvements. The X-Hybrid is can also store surplus energy in batteries for later use. It is important to understand that this is a hybrid solar PV inverter and battery storage controller. This means it needs to be sized just like a regular inverter would be and, if it is being retrofitted, will replace the existing inverter. AC attributes Max power: 12000W Max current: 19.3A Number of phases: 3 DC attributes Max power 18000W Max Isc current 20A Max voltage 1000V Start up voltage 200V System Max efficiency 98% IP rating IP65 Weight 30kg Dimensions 503*503*199mm Key features In-built EPS changeover switch Supports up to 150% oversizing Can work at full capacity down to -35C 30A Charge/discharge capability On-grid and off-grid use Includes WiFi dongle

Read more less

Part No: X3-HYBRID-G4-15.0-V2 Storage Systems - Hybrid Inverter SolaX's X-Hybrid three-phase inverter is the most updated version of their hybrid inverters range. This adaptable and expandable device caters to residential and commercial purposes, with the possibility to incorporate several inverters in parallel allowing for scalable battery storage used in commercial settings. The inverter also comes with a feature called EPS (Emergency Power Supply), which utilizes extra changeover devices. Multiple communication options are available, and the device can be controlled remotely. Some of its significant features are maximum efficiency of 98%, dual MPTT, remote monitoring, an IP65 rating, and a 10-year warranty. Key features: In-built EPS changeover switch Supports up to 150% over-sizing 30A Charge/discharge capability On-grid and off-grid use Includes WiFi dongle Looking to expand your system capacity? See Solax EPS Parallel Box options  – Connect up 6 hybrid inverters with a maximum of 60kW – Connect up 10 hybrid inverters with a maximum of 150kW Wi-Fi is now included with Solax X3-Hybrid-G4 V2 product so no need to purchase additional Wi-Fi equipment Supplier Part No: X3-Hybrid 15.0-D G4 V2 with WiFi Weight: 30 kg Rated Power: 15,000 W Min PPT Voltage: 180 V Max PPT Voltage: 950 V DC Startup Voltage: 200 V DC Shutdown Voltage: 200 V Max Input Voltage: 950 V Max DC Power: 18,000 W Max AC Power (5 Minutes): 15,001 W Surge AC Power (1 Second): 15,002 W Max DC Current: 26 A Max DC Inputs: 2 Has DC Fuses: 0 Connector: SUNCLIX   Included Connectors: 2 Euro Efficiency: 97 % Transformer: None MPPT Quantity : 2 Has Integrated DC Switch: No Warranty: 5 years

Read more less

Growatts MIN 2500-6000TL-X series are the most up-to-date smart inverter solution for residential rooftop solar systems. It sports a compact design with a touch key and OLED display thats simple and easy to use and boasts a max efficiency of up to 98.4% MIN inverters require a meter to achieve the export limit function. AC attributes Max power: 6000W Max current: 27.2A Number of phases: 1 DC attributes Number of MPPT 2 V range of MPPT 80 - 550V Max power 8100W Max Isc current 16.9A Max voltage 550V Start up voltage 100V System Max efficiency 98.4% IP rating IP65 Built in protection Type III AC/DC surge  Export limitations With meter or CT Weight 10.8kg Dimensions375x350x160mm Communication RS485, USB, (wifi, GPRS,RF,LAN optional) Warranty (extensions) 10 years Key features Dual MPPT Trackers Touch Key and OLED Display Efficient Power Generation Support Export Control

Read more less

The new X range of residential inverters is a smaller, lighter version of it's mini-S predecessor. The sleek, minimal design makes it an aesthetic choice at a competitive price. The low start up voltage and wide voltage range allow flexibility in string design.  MIC inverters require a meter to achieve the export limit function.   AC attributes Max power: 1500W Max current: 7.1A Number of phases: 1 DC attributes Number of MPPT 1 V range of MPPT 50 - 500V Max power 2100W Max Isc current 16A Max voltage 500V Start up voltage 50V System Max efficiency 97.4% IP rating IP65 Built in protection Type III AC/DC surge  Export limitations With meter or CT Weight 6kg Dimensions 274x254x138mm Communication RS485, USB, (wifi, GPRS,RF,LAN optional) Warranty 10 years Key features Lightweight Build in SPD protection Indoor or outdoor installation

Read more less

The Shinelink-X is a quick plug and play way to provide monitoring for a Growatt inverter. Generation can then be monitored via the online portal or shinephone app. The Shinelink-X hub works with the X and XE range of Growatt inverters (1 RF dongle included). Note: To pair and register use the Serial Number of the Shinelink-X box not on the stick. 

Read more less

The ShineLAN-X dongle works with the X, MIC-X and XE range of Growatt inverters. Easy to use alternative to the Growatt Shinelink-X, letting you connect a Growatt inverter directly into your customer's router by hardwired cable. Alternatively it can be used in conjunction with Power Line Adaptors where the standard Growatt Wifi dongle won't work. Plug-and-play commissioning Direct data exchange with Router via Rj45 Remote firmware updating for inverter Free online monitoring via Shine Server

Read more less

The Phoenix 24/1200 VE.Direct inverter allows you to power domestic equipment – requiring 230V  – using ‘leisure’ or ‘automotive’ batteries rated at 12V, 24V or 48V DC.  This unit has the UK plug. Features of the Phoenix Inverter 24/1200 VE.Direct VE.Direct communication port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation. Monitor, operate & control your system VictronConnect lets you get live status information and configure your Phoenix Inverter 24/1200 VE.Direct when connected to a VE.Direct Bluetooth Smart Dongle. The REC040010210R is the correct controller for the Phoenix Inverter VE.Directs.   Brand Victron Energy Manufacturer Part Number PIN242121400 gtin 8719076056119 Voltage 24V Cont. Output Power at 25°C 1200VA Peak Power 2200W Output AC Voltage 230V Efficiency 91% Protection Category IP21 Dimensions H117 x W232 x D327mm Weight 7.4Kg Warranty 5 Years Bluetooth Enabled No Plug Type UK Country of Manufacture China

Read more less

Part No: SUN-16.0 Storage Systems - Hybrid Inverter The 16kW single-phase hybrid inverter is the biggest addition to Sunsynk’s low voltage (48V) single-phase inverter range. It’s suitable for off-grid, grid support, backup, and self-consumption PV systems and can also be used in both three-phase and single-phase parallel applications.  In terms of functionality, compatibility, and related accessories, it’s similar to the 5kW & 8kW units but particularly suited to large domestic and small commercial installations.   “It’s the biggest single phase all-in-one inverter with everything built in, in the world”, Keith Gough, Sunsynk CEO. A true monster!  Additional features:  A total of 15x inverters can be connected in a three-phase configuration (five units per phase) - giving a maximum power output of 240kW  Three inverters can be connected in a single-phase configuration giving a total power of 48kW  Contains 3x MPPTs to allow for flexible PV array designs and improved efficiency  Programmable multiple operation modes: on-grid/off-grid & UPS  IP65 protection rating  Wi-Fi dongle as standard – enabling remote monitoring via the Sunsynk cloud  Compatible with leading lithium battery brands such as Hubble Lithium, Pylontech LV, Freedomwon and Kodak (BL3.6)  Sunsynk inverter and Freedom Won battery pairing : 10-year extended warranty. For installations with Pylontech, REVOV and Hubble Lithium batteries use this BMS cable For installations with Freedom Won batteries use this BMS cable Installations with Sunsynk products need to be registered to gain full activation of the warranty. Register here>> Equipment warranty registration needs to take place within 7 (seven) days of commissioning of the project, failure to register the warranty may result in the warranty being made void.   Supplier Part No: SUNSYNK-16K-SG01LP1 Weight: 56 kg Rated Power: 16,000 W Min PPT Voltage: 250 V Max PPT Voltage: 450 V DC Startup Voltage: 150 V DC Shutdown Voltage: 0 V Max Input Voltage: 450 V Max DC Power: 18,000 W Max AC Power (5 Minutes): 16,001 W Surge AC Power (1 Second): 32,000 W Max DC Current: 66 A Max DC Inputs: 6 Has DC Fuses: 0 Connector: Screw Terminal   Included Connectors: 12 Euro Efficiency: 97.6 % Transformer: None MPPT Quantity : 3 Has Integrated DC Switch: Yes Warranty: 5 years

Read more less

The XLR charger tester is a module specifically designed to measure a wheelchair’s charge/discharge current and battery voltage. The XLR charger tester is inserted in the connection between the charge device and the wheelchair charge plug. The XLR charger tester measures voltage from 0.0V to 30.0V and current from 0.0A to 19.9A. Brand Victron Energy Manufacturer Part Number CHT000100000 Warranty 5 Years Country of Manufacture Netherlands

Read more less

The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features.   Features Two AC Outputs The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example can be connected to this output (second output available on models rated at 3 kVA and more). Virtually unlimited power thanks to parallel operation Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity. Three phase capability In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The MultiPlus can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number PMP485021010 Voltage 48 Transfer Switch (A) 100 Cont. Output Power at 25°C (VA) 5000 Peak Power (W) 10000 Max Efficiency 95% Zero Load Power (W) 35 Charge Current House Battery (A) 70 Charge Current Starter Battery (A) 4 (12 V and 24 V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off Yes Protection Category IP21 Dimensions H444 x W328 x D240mm Weight (kg) 30 Warranty 5 Years Country of Manufacture India

Read more less

CLICK HERE FOR SPEC SHEETS The new style MultiPlus is set to replace the earlier MultiPlus Compact range. It is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology and a high-speed AC transfer switch in a single compact enclosure.   Features Uninterrupted AC power (UPS function) In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption Remote Monitoring and Control Monitor and control your MultiPlus and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your MultiPlus to setting a Geofence for hire vehicles and more… Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.  PowerControl – Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).   Brand Victron Energy Manufacturer Part Number PMP121800000 Voltage 12 Transfer Switch (A) 16 Cont. Output Power at 25°C (VA) 800 Peak Power (W) 1600 Max Efficiency 92% Zero Load Power (W) 7 Charge Current House Battery (A) 35 Charge Current Starter Battery (A) 1 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay Yes Remote on-off Yes Protection Category IP21 Dimensions H360 x W240 x D100mm Weight (kg) 6.4 Warranty 5 Years Country of Manufacture India

Read more less

CLICK HERE FOR SPEC SHEETS With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.   Features Bluetooth inside With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Download the Victron Bluetooth app Use a smartphone or other Bluetooth enabled device to – customize settings, – monitor all important data on single screen, – view historical data, and to – update the software when new features become available. Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting. Midpoint voltage monitoring One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. We recommend the Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries. Very low current draw from the battery Current consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown. After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days. Bi-stable alarm relay Prevents increased current draw in case of an alarm. Brand Victron Energy Manufacturer Part Number BAM030712000R Supply Voltage Range 6.5-70 VDC Battery Capacity (Ah) 1-9999 Temperature Sensor Optional VE.Direct Communication Port Yes Protection Category IP55 Front Bezel 69 x 69mm Body Diameter & Depth 52 x 31mm Warranty 5 Years Country of Manufacture Malaysia

Read more less

CLICK HERE FOR SPEC SHEETS The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.   Features Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Split phase and three phase capability Two units can be configured for split phase, and three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. For more detail please enter parallel in the search box on our website. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).   Brand Victron Energy Manufacturer Part Number QUA125020000 Voltage 12 Transfer Switch (A) Yes Cont. Output Power at 25°C (VA) 5000 Peak Power (W) 10000 Max Efficiency 94% Zero Load Power (W) 30 Charge Current House Battery (A) 220 Charge Current Starter Battery (A) 4 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay 3x Remote on-off Yes Protection Category IP21 Dimensions H470 x W350 x D280mm Weight (kg) 34 Warranty 5 Years Country of Manufacture India

Read more less

Inverters allow you to power domestic equipment – requiring 230V/120V AC – using ‘leisure’ or ‘automotive’ batteries rated at 12V, 24V or 48V DC.   Features VE.Direct communication port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage 210 – 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load and alarms Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote on/off A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector. DC connection with screw terminals No special tools needed for installation. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number PIN482120400 Voltage 48 VA 1200 Peak Power (W) 2200 Max Efficiency 92% Plug Type UK IP Rating IP21 Dimensions (Including Terminals) H117 x W232 x D327mm Weight (kg) 7.4 Warranty 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS   The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.   Features Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Split phase and three phase capability Two units can be configured for split phase, and three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. For more detail please enter parallel in the search box on our website. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). Brand Victron Energy Manufacturer Part Number QUA248020010 Voltage 24 Transfer Switch (A) Yes Cont. Output Power at 25°C (VA) 8000 Peak Power (W) 16000 Max Efficiency 94% Zero Load Power (W) 60 Charge Current House Battery (A) 26.4 Charge Current Starter Battery (A) 4 (12V and 24V models only) Battery Temperature Sensor Yes Programmable Relay 3x Remote on-off Yes Protection Category IP21 Dimensions H470 x W350 x D280mm Weight (kg) 45 Warranty 5 Years Country of Manufacture India

Read more less

The MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges a battery banks. The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.   Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC125070421 GTIN 8719076051213 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated charge current 70A Nominal PV power, 12V 1000W Nominal PV power, 24V 2000W Max. PV Short Circuit Current 35A Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions, 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can, VE.Direct and Bluetooth Dimensions H185 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

The MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges a battery banks. The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.   Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC125085511 Battery Voltage 12 / 24 / 48V Auto Select (36V: manual) Rated Charge Current 85A Nominal PV Power, 12V 1200W Nominal PV Power, 24V 2400W Max. PV Short Circuit Current 70A (max 30A per MC4 conn.) Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions, 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can, VE.Direct and Bluetooth IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

Solarcable L=5m/6sqmm MC4-M/F Connection Brand Victron Energy Manufacturer Part Number SCA000500100 Warranty 5 Years

Read more less

Solarcable L=10m/6sqmm MC4-M/F Connection Brand Victron Energy Manufacturer Part Number SCA001000100 Warranty 5 Years

Read more less

Shunt 500A/50mV Brand Victron Energy Manufacturer Part Number SHU500050100 Warranty 5 Years

Read more less

MEGA-fuse 200A/32V (5 pack) Brand Victron Energy Manufacturer Part Number CIP136200010 Warranty 5 Years Appr. Voltage Drop 80 mV Cold Resistance 0.25  

Read more less

MEGA-fuse 200A/58V for 48V products (1 pc)   Brand Victron Energy Manufacturer Part Number CIP137200010 Warranty 5 Years Country of Manufacture India Appr. Voltage Drop 80 mV Cold Resistance 0.25

Read more less

One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. The input for the charger is 230V at 50/60HZ. Charge voltage can be measured directly on the battery terminals in order to compensate for voltage loss due to cable resistance. An external sensor allows measuring battery temperature and compensating charge voltage accordingly.   Features Perfect chargers for any type of battery Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular, sealed maintenance free batteries must be charged correctly in order to ensure a long service life. Overvoltage will result in excessive gassing and venting of a sealed battery. The battery will dry out and fail. Suitable for AC and DC supply (AC-DC and DC-DC operation) Except for the 3-phase input models, the chargers also accept a DC supply. Controlled charging Every TG Charger has a microprocessor, which accurately controls the charging in three steps. The charging process takes place in accordance with the IUoUo characteristic and charges more rapidly than other processes. Use of TG Chargers as a power supply As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Two outputs to charge 2 battery banks (24V models only) The TG Chargers feature 2 isolated outputs. The second output, limited to approximately 4A and with a slightly lower output voltage, is intended to top up a starter battery. To increase battery life: temperature compensation Every Skylla TG Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries which otherwise might be overcharged and dry out due to venting. Battery voltage sense In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SDTG2400501 Voltage 24 Charger Current House Battery 50A Charger Current Starter Battery 4A Recommended Battery Capacity 150 – 500Ah Battery Connection M8 Studs Outputs 1+1 Temperature Sensor Yes Can Be Used As Power Supply Yes IP Rating IP21 Dimensions H365 x W250 x D147mm Weight (kg) 5.5 Warranty 5 Years Country of Manufacture Malaysia

Read more less

Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).  Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI241210110R Input Voltage Range 16-35V Under Voltage Shutdown 14V Under Voltage Restart 15V Nominal Output Voltage 12.2V Output Voltage Adjust Range 10-15V Short Circuit Output Current 39A Cont. Output Power at 25°C 110W DC Connection Screw Terminals Protection Category IP43 Dimensions H100 x W113 x D47mm Weight (kg) 0.42 Warranty 5 Years

Read more less

Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).  Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI242428110 Input Voltage Range 16-35V Under Voltage Shutdown 14V Under Voltage Restart 15V Nominal Output Voltage 24.2V Output Voltage Adjust Range 20-30V Short Circuit Output Current 30A Cont. Output Power at 25°C 320W DC Connection Screw Terminals Protection Category IP43 Dimensions H130 x W186 x D70 mm Weight (kg) 1.3 Warranty 5 Years

Read more less

Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).  Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only.    PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI244810110 Input Voltage Range 16-35V Under Voltage Shutdown 14V Under Voltage Restart 15V Nominal Output Voltage 48.2V Output Voltage Adjust Range 40-60V Short Circuit Output Current 19A Cont. Output Power at 25°C 120W DC Connection Screw Terminals Protection Category IP43 Dimensions H100 x W113 x D47mm Weight (kg) 0.42 Warranty 5 Years

Read more less

Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).  Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only.    PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI484828110 Input Voltage Range 32-70V Under Voltage Shutdown 28V Under Voltage Restart 30V Nominal Output Voltage 48.2V Output Voltage Adjust Range 40-60V Short Circuit Output Current 25A Cont. Output Power at 25°C 320W DC Connection Screw Terminals Protection Category IP43 Dimensions H130 x W186 x D70 mm Weight (kg) 1.3 Warranty 5 Years

Read more less

 A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.   MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Load output The intelligent Load output function prevents damage caused by running batteries ‘flat’. You can configure the voltage at which SmartSolar disconnects a load – thereby preventing excessive drain on your batteries. And here’s the clever bit: SmartSolar will attempt a 100% recharge every day. If it can’t – during periods of poor weather – it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC075010060R GTIN 8719076040798 Battery Voltage 12/24 Auto Select Rated Charge Current 10A Nominal PV Power, 12V 145W Nominal PV Power, 24V 290W Max. PV Short Circuit Current 13A Maximum PV Open Circuit Voltage 75V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H100 x W113 x D40mm Weight 0.5Kg Warranty 5 Years

Read more less

Use this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output:  VE.Bus BMS: the Inverter will be switched off when the batteries are empty BlueSolar MPPT Charger: connecting an inverter directly on the load output of a BlueSolar MPPT Charger is not possible; the inverter needs to be connected to the battery. Then use this cable to switch the inverter on and off with the load output. The load output of an MPPT 75/15 or MPPT 100/15, for example, can be used to control an inverter. Some inverters will switch on when the remote control input is pulled high. The remote control input of other inverters must be pulled down to switch on. Pull down to switch on is needed for the Victron inverters model Phoenix 12/180, 24/180, 12/350 and 24/350. These inverters should be interfaced to the load output of the MPPT 75/15 or MPPT 100/15 with the inverting remote on-off cable. All Phoenix Inverters rated at 3kVA and more and all Multi C’s, Multi’s and Quattro’s also require active pull down to switch on, and the inverting remote on-off cable can be used to interface between the remote on-off terminal and a source signal that turns high when switch on is required.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS030550120 Warranty 5 Years

Read more less

Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A   CLICK HERE FOR SPEC SHEET   Brand Victron Energy Manufacturer Part Number SCC010030050 GTIN 8719076046226 Battery Voltage 12/24 V automatic system voltage detection Rated Charge Current 30A Maximum Solar Voltage 28V / 55V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H101 x W184 x D47mm Weight 0.3Kg Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life. MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your BlueSolar MPPT charger by attaching a bluetooth dongle and pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Full output current up to 40°C (104°F). Flexible charge algorithm Fully programmable charge algorithm (see the software page on our website), and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Real-time data display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC115045222 GTIN 8719076053033 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 45A Nominal PV power 12V: 650W / 24V: 1300W / 36V: 1950W / 48V: 2600W Max. PV short circuit current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Maximum efficiency 98% Charge Algorithm multi-stage adaptive (eight pre-programmed algorithms) Data Communication Port VE.Direct Protection Category IP43 (electronic components), IP22 (connection area) Dimensions H130 x W186 x D70mm Weight 1.25Kg Warranty 5 Years

Read more less