Products

When the CAN bus is not powered by a Skylla-I or a MPPT, you will need the new VE.Can Power Cable to supply the power. Brand Victron Energy Manufacturer Part Number ASS030690000 Warranty 5 Years

Read more less

The VE.Can resistive tank sender adapter allows a standard resistive tank level sender to connect to the Color Control GX. It is compatible with both European standard 0-180 Ohm and United States standard 240-30 Ohm tank level senders and is accurate to ±1%. It is easily configurable to resistive senders from fuel, fresh water, waste water, well water, oil and black water (sewage) tanks. It supports up to 16 tanks of each type. The unit is a simple setup with two small rotary switches and it gets its power from the VE.Can network. When you use a Skylla-i or a MPPT with CAN bus in the system, the power to the CAN bus will be supplied by either one of them. When the CAN bus is not powered by a Skylla-I or a MPPT, you will need the new VE.Can Power Cable to supply the power. Brand Victron Energy Manufacturer Part Number BPP900600100 Warranty 5 Years

Read more less

The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB. Brand Victron Energy Manufacturer Part Number ASS030700000 Warranty 5 Years

Read more less

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B. See the manual for details on which cable to use for which brand of batteries. Brand Victron Energy Manufacturer Part Number ASS030710018 Cable Length 1.8m Warranty 5 Years

Read more less

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B. See the manual for details on which cable to use for which brand of batteries. Brand Victron Energy Manufacturer Part Number ASS030720018 Warranty 5 Years Cable Length 1.8m

Read more less

Use this cable to connect a Victron product with a VE.Can port to a NMEA2000 network. Brand Victron Energy Manufacturer Part Number ASS030520200 Warranty 5 Years

Read more less

 Using the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect app. View information wirelessly such as battery status and solar panel power, plus other useful data.  The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers. With the VE.Direct to Bluetooth Smart dongle you can get live status info, see historical values as well as configure Victron products.The dongle works together with the VictronConnect app, available for both Android and iOS devices. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS030536011 Weight (kg) 0.27 Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model.   Brand Victron Energy Manufacturer Part Number ASS030531203 Cable Length 0.3m Warranty 5 Years

Read more less

  The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030530203 Cable Length 0.3m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model.   Brand Victron Energy Manufacturer Part Number ASS030531209 Cable Length 0.9m Warranty 5 Years

Read more less

  The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030530209 Cable Length 0.9m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model.   Brand Victron Energy Manufacturer Part Number ASS030531209 Cable Length 0.9m Warranty 5 Years

Read more less

  The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030530218 Cable Length 1.8m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030531320 Cable Length 10m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model.   Brand Victron Energy Manufacturer Part Number ASS030530310 Cable Length 10m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030531230 Cable Length 3m Warranty 5 Years

Read more less

  The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030530230 Cable Length 3m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030531250 Cable Length 5m Warranty 5 Years

Read more less

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model.   Brand Victron Energy Manufacturer Part Number ASS030530250 Cable Length 5m Warranty 5 Years

Read more less

Using the VE.Direct to LoRaWAN module you can connect your BMV, MPPT or Phoenix Inverter to the Victron Remote Management portal. View information such as battery status or solar power wherever you are on your desktop or mobile phone. Remote Monitoring and Control You can check the status of your connected products on our free remote monitoring website: the VRM Online Portal. To get an impression of the VRM Online Portal, and use the ‘Try Our Demo’ button. The portal is free of charge. Long Range Wide Area Network LoRaWAN is a wireless network that operates on the 868Mhz frequency. It has a long range and uses small amounts of power. The VE.Direct LoRaWAN module can send hourly data updates via this network. You do not need a subscription to make use of this network. If you do not have coverage in your region it is possible to add your own gateway. Brand Victron Energy Manufacturer Part Number ASS030538010 Warranty 5 Years

Read more less

    Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models. Note that it’s not necessary to use this cable on the larger SmartSolar models, as they feature an onboard Remote On/Off terminal. The charger will be enabled when the signal on the cable is high. The charger is disabled when the source signal is pulled low or left free floating. Note that when using this cable, it’s not possible to use the VE.Direct port for any other purpose. Such as connecting to a GX device, or for example a VE.Direct Bluetooth Smart dongle on a BlueSolar charger.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS030550320 Warranty 5 Years

Read more less

VE.Direct to BMV60xS Cable 1.5m Brand Victron Energy Manufacturer Part Number ASS030532215 GTIN 8719076019763 Cable Length 1.5m Warranty 5 Years

Read more less

VE.Direct to BMV60xS Cable 3m Brand Victron Energy Manufacturer Part Number ASS030532230 GTIN 8719076019763 Cable Length 3m Warranty 5 Years

Read more less

This NMEA2000 drop cable makes the BMV-700 information available to an NMEA2000 networks. Battery information such as voltage, current and state of charge can be displayed on common purpose displays from other manufacturers which accept the NMEA2000 data being sent. Limitations: The cable does not work with other VE.Direct products, such as Solar Chargers, Inverters and also not with the BMV-712 Smart. When used in combination with a BMV-702 there is limited functionality with regards to the AUX function in the BMV: When used to measure starter battery voltage, that voltage will be transmitted to the NMEA2000 network. But when used to measure temperature and or mid-voltage, that data will not be transmitted on the NMEA2000 network. Brand Victron Energy Manufacturer Part Number ASS030520310 Warranty 5 Years

Read more less

VE.Direct to RS232 interface Brand Victron Energy Manufacturer Part Number ASS030520500 Warranty 5 Years

Read more less

The VE.Direct to VE.CAN interface cable can be used to make BMV-700 information available on a VE.Can network. Where it can be read by a Color Control GX for example. Limitations: The interface cable does not work with other VE.Direct products, such as Solar Chargers, Inverters and also not with the BMV-712 Smart. When used in combination with a BMV-702 there is limited functionality with regards to the AUX function in the BMV: When used to measure starter battery voltage, that voltage will be transmitted to VE.Can. But when used to measure temperature and or mid-voltage, that data will not be transmitted on the VE.Can network.  Brand Victron Energy Manufacturer Part Number ASS030520410 Warranty 5 Years

Read more less

The VE.Direct TX digital output cable can be used in combination with the BlueSolar and SmartSolar MPPT chargers. It supports the following applications: Solar lighting applications Virtual load output Lighting Applications The cable is designed for lighting applications in solar energy systems.Energy consumption can be significantly reduced by the ability to dim lighting when needed. Lower power consumption will reduce the overall system cost. Also, the availability of the lighting will increase, even in case of a partially charged battery in low sun.The cable connects the TX output of the VE.Direct connector of a MPPT charger with the PWM dimmer input of the LED driver. Virtual load output The cable is designed for adding load output functionality to the larger MPPT chargers (MPPT 100/30 and larger) that do not have a load output. The cable connects the TX output of the VE.Direct connector of a MPPT charger with a battery protect or a solid state relay to switch a load on or off.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS030550500 Warranty 5 Years

Read more less

VE.Net GMDSS panel remotely monitors the Victron Skylla-TG GMDSS charger. Brand Victron Energy Manufacturer Part Number VPN000200000 Dimensions L65 x W120 x H40mm Weight (kg) 0.1 Warranty 5 Years

Read more less

The Venus GX is the communication-centre of your installation. Venus allows you to talk to all components in your system and ensure they are working in harmony. Monitoring of live data, and changing settings is performed by using your smartphone (or other device) via our free-to-use Victron Remote Management Portal (VRM). Intuitive system overview – all you need to know As soon as you ‘log on’ Venus GX provides an instant overview of your system: Battery state of charge; present power consumption; power harvest from PV; power provision from mains/generator.  The full power of Victron Remote Management Victron Remote Management (VRM) provides you with full access to the very extensive controls and settings of all system-components which are connected to either your CCGX or Venus GX. It allows remote user and installer login – from anywhere, at anytime. This powerful application also provides for hassle-free diagnostic checks and analysis of archived information. Automatic Generator start/stop The Venus GX can be programmed to auto-start your generator – triggered by low-voltage; high-demand; or battery state of charge. It can be further tailored to delay ignition until the end of ‘quiet’ periods – avoiding accidental nuisance at dead of night. Remote Console – control everything from anywhere… Remote Console provides visual access to the live data and settings of your Venus GX …and because it’s remote – you can do that from anywhere in the world. ESS: Energy Storage Systems – 24 hour Monitoring The Venus GX manages Energy Storage Systems. It keeps back-up batteries at 100% ; kicks-in during power-cuts; and diverts excess (solar) power to self-consumption – saving you money. For examples and more detailed information see the ESS (Energy Storage System) manual. Remotely Monitor your boat or motorhome electrics Planning a trip? Remote monitoring of your Venus GX allows you to make sure your boat or motorhome are ready to go. Venus GX also allows you to talk to connected equipment from other manufacturers. And with Venus GX you can check the tanks, too.  CLICK HERE FOR SPEC SHEET   Brand Victron Energy Manufacturer Part Number BPP900400100 Power Supply Voltage Range 8-70 V DC VE.Direct Ports (always isolated) 2 VE.Bus (always isolated) 2 paralleled RJ45 sockets VE.Can 2 paralleled RJ45 sockets – isolated Wifi Built-in Temperature sense inputs 2 Digital Inputs 5 Max. VE.Direct devices 6 Dimensions H45 x W143 x D96mm Warranty 5 Years

Read more less

Wall mount enclosure for 65 x 120mm GX panels  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS050300010 Dimensions H88 x W130 x D40mm Warranty 5 Years

Read more less

Wall mount enclosure for BMV or MPPT Control  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS050500000 Dimensions H88 x W130 x D47mm Warranty 5 Years

Read more less

  Wall Mount for Blue Smart IP65 Charger 12/10, 12/15, 24/8  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BPC920100200 Dimensions H134 x W145 x D72mm Warranty 5 Years

Read more less

Easily mount a BMV and MPPT Control on a wall.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS050600000 Dimensions H244 x W135 x D75mm Warranty 5 Years

Read more less

Wall mount enclosure for Color Control GX  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS050400000 Dimensions H163 x W135 x D72mm Warranty 5 Years

Read more less

The XLR charger tester is a module specifically designed to measure a wheelchair’s charge/discharge current and battery voltage. The XLR charger tester is inserted in the connection between the charge device and the wheelchair charge plug. The XLR charger tester measures voltage from 0.0V to 30.0V and current from 0.0A to 19.9A. Brand Victron Energy Manufacturer Part Number CHT000100000 Warranty 5 Years Country of Manufacture Netherlands

Read more less

Zigbee to RS485 converter CLICK HERE FOR SPEC SHEET gtin 8719076048268 Brand Victron Energy Manufacturer Part Number ASS300420100 Warranty 5 Years Dimensions H70 x W50 x D24mm Protoco Zigbee2007 Distance Visible, open transmission distance : 1600 meters

Read more less

Zigbee to USB converter CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ASS300400200 Power USB Port 5V Dimensions H70 x W50 x D24mm Warranty 5 Years

Read more less

  The SmartSolar Control Display is a pluggable LCD display for the SmartSolar Charge Controllers. Simply remove the rubber seal that protects the plug on the front of the controller and plug-in the display. Manufacturer: Victron EnergyPart Number: SCC950100000Weight: 0.2kgWarranty: 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS Multifunctional, with intelligent power management. The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus ha several advanced features, as outlined below. Two AC Outputs The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on the models rated at 3kVA and more). Virtually unlimited power thanks to parallel operation Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units. for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity. Three phase capability In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54kVA three phase inverter and 1260A charger can be built. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power. Alterntively, a split phase AC can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. PowerControl – Dealing with limited generator, shore side or generator power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 20A per 3kVA MultiPlus at 120VAC). With the MultiPlus Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficent shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Four stage adaptive charger and dual bank battery charging The main output provides a powerful charge to the battery system by means of advacned ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptvie charge process is described in more detailes on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery. System configuring has never been easier After installation, the MultiPlus is ready to go.If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed!Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick COnfigure and VE.Bus System Configurator) is available to configure several new, advanced features. Manufacturer: Victron EnergyPart Number: PMP122301102Weight: 19kgLength: 218mmWidth: 258mmHeight: 362mmInput Voltage: 9.5 – 17 VOutput Voltage: 120VACContinuous Output Power: 2400W at 25°CPeak Output Power: 6000WCharger Output Current: 120ATransfer Switch: 120AFrequency: 60HzOperating Temperature Range: -40 to +65°C (fan assisted cooling)Output Wave Form: Pure Sine WaveWarranty: 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS Multifunctional, with intelligent power management. The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus ha several advanced features, as outlined below. Two AC Outputs The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on the models rated at 3kVA and more). Virtually unlimited power thanks to parallel operation Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units. for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity. Three phase capability In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54kVA three phase inverter and 1260A charger can be built. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power. Alterntively, a split phase AC can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. PowerControl – Dealing with limited generator, shore side or generator power The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 20A per 3kVA MultiPlus at 120VAC). With the MultiPlus Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. PowerAssist – Boosting the capacity of shore or generator power This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficent shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Four stage adaptive charger and dual bank battery charging The main output provides a powerful charge to the battery system by means of advacned ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptvie charge process is described in more detailes on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery. System configuring has never been easier After installation, the MultiPlus is ready to go.If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed!Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick COnfigure and VE.Bus System Configurator) is available to configure several new, advanced features. Manufacturer: Victron EnergyPart Number: PMP123021102Weight: 19kgLength: 218mmWidth: 258mmHeight: 362mmInput Voltage: 9.5 – 17 VOutput Voltage: 120VACContinuous Output Power: 2400W at 25°CPeak Output Power: 6000WCharger Output Current: 120ATransfer Switch: 120AFrequency: 60HzOperating Temperature Range: -40 to +65°C (fan assisted cooling)Output Wave Form: Pure Sine WaveWarranty: 5 Years

Read more less

Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem free, to any load. Features SinusMax – Superior engineering Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem-free, to any load. Extra start-up power A unique feature of the SinusMax technology is very high start-up power. Conventional high frequency technology does not offer such extreme performance. Phoenix Inverters, however, are well suited to power up difficult loads such as computers and low power electric tools. To transfer the load to another AC source: the automatic transfer switch For our lower power models we recommend the use of our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. LED diagnosis Please see manual for a description. Remote on/off switch Connector for remote on/off switch available on all models. click here for spec sheet Weight 7.4 kg Dimensions 362 × 232 × 117 mm Brand Victron Energy Input Voltage 24V Output Voltage 110V Wattage (W) 1000W Region North America Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem free, to any load. Features SinusMax – Superior engineering Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem-free, to any load. Extra start-up power A unique feature of the SinusMax technology is very high start-up power. Conventional high frequency technology does not offer such extreme performance. Phoenix Inverters, however, are well suited to power up difficult loads such as computers and low power electric tools. To transfer the load to another AC source: the automatic transfer switch For our lower power models we recommend the use of our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. LED diagnosis Please see manual for a description. Remote on/off switch Connector for remote on/off switch available on all models. DIP switch for 50/60Hz selection (48/350 model only) Available with different output sockets click here for spec sheet Weight 6.5 kg Dimensions 305 × 194 × 104 mm Brand Victron Energy Input Voltage 48V Output Voltage 110V Wattage (W) 700W Region North America Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS   Multifunctional Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation. Models: 3000VA, 5000VA, 8000VA, 10000VA, 15000VA Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Two AC inputs with integrated transfer switch The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source. Two AC Outputs The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output. Virtually unlimited power thanks to parallel operation Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power.Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. Three phase capability Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded. PowerAssist – Boosting shore or generator power This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232). Remote Monitoring and control Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. Remote configuring When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.   Weight 34 kg Dimensions 280 × 350 × 470 mm Brand Victron Energy Input Voltage 12V Output Voltage 110V Current (Amps) 200A Wattage (W) 4000W Region North America Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS   Multifunctional Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation. Models: 3000VA, 5000VA, 8000VA, 10000VA, 15000VA Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Two AC inputs with integrated transfer switch The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source. Two AC Outputs The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output. Virtually unlimited power thanks to parallel operation Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power.Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. Three phase capability Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded. PowerAssist – Boosting shore or generator power This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232). Remote Monitoring and control Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. Remote configuring When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely. Weight 51 kg Dimensions 280 × 350 × 470 mm Brand Victron Energy Input Voltage 48V Output Voltage 230V Wattage (W) 8000W Current (Amps) 140A Region UK, Europe, French, Australia/New Zealand, Worldwide Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS   Multifunctional Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation. Models: 3000VA, 5000VA, 8000VA, 10000VA, 15000VA Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Two AC inputs with integrated transfer switch The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source. Two AC Outputs The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output. Virtually unlimited power thanks to parallel operation Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power.Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. Three phase capability Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded. PowerAssist – Boosting shore or generator power This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232). Remote Monitoring and control Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. Remote configuring When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely. Weight 72 kg Dimensions 344 × 488 × 572 mm Brand Victron Energy Input Voltage 48V Output Voltage 230V Current (Amps) 200A Wattage (W) 12000W Region UK, Europe, French, Australia/New Zealand, Worldwide Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS   Multifunctional Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation. Models: 3000VA, 5000VA, 8000VA, 10000VA, 15000VA Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Two AC inputs with integrated transfer switch The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source. Two AC Outputs The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output. Virtually unlimited power thanks to parallel operation Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power.Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. Three phase capability Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded. PowerAssist – Boosting shore or generator power This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232). Remote Monitoring and control Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. Remote configuring When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely. Weight 30 kg Dimensions 240 × 328 × 444 mm Brand Victron Energy Input Voltage 48V Output Voltage 230V Current (Amps) 70A Wattage (W) 4000W Region UK, Europe, French, Australia/New Zealand, Worldwide Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

CLICK HERE FOR SPEC SHEETS   Multifunctional Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation. Models: 3000VA, 5000VA, 8000VA, 10000VA, 15000VA Two AC Inputs & two AC Outputs The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output. Unique PowerAssist feature The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery. Virtually unlimited power thanks to parallel operation Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities. Remote Monitoring and Control Monitor and control your Quattro and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more… Two AC inputs with integrated transfer switch The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source. Two AC Outputs The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output. Virtually unlimited power thanks to parallel operation Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity. Split phase options Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power.Alternatively, a split phase AC source can be obtained by connecting our autotransformer (see data sheet on www.victronenergy.com) to a ‘European’ inverter programmed to supply 240V / 60Hz. Three phase capability Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity. PowerControl – Dealing with limited generator, shore side or grid power The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded. PowerAssist – Boosting shore or generator power This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. Solar energy: AC power available even during a grid failure The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.Loss of mains detection software is available. System configuring In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications). On-site Monitoring and control Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232). Remote Monitoring and control Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. Remote configuring When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely. Weight 41 kg Dimensions 280 × 350 × 470 mm Brand Victron Energy Input Voltage 48V Output Voltage 230V Wattage (W) 6500W Region UK, Europe, French, Australia/New Zealand, Worldwide Current (Amps) 110A Inverter Type Pure Sine Wave Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.   Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 99%. Flexible charge algorithm Fully programmable charge algorithm, and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC125110441 GTIN 8719076050926 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated Charge Current 100A Nominal PV Power, 12V 1450W Nominal PV Power, 24V 2900W Max. PV Short Circuit Current 70A Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions | 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less